Exam Details
| Subject | Maintenance Of Electronic Equipment | |
| Paper | ||
| Exam / Course | Diploma In Electronics And Communication Engineering (DECVI)/ Advanced Level Certificate Course In Electronics And Communication Engineering (ACEVI)/ | |
| Department | School of Engineering & Technology (SOET) | |
| Organization | indira gandhi national open university | |
| Position | ||
| Exam Date | June, 2016 | |
| City, State | new delhi, |
Question Paper
No. of Printed Pages: 2 IBIEL-037I
DIPLOMA -VIEP -ELECTRONICS AND
COMMUNICATION ENGINEERING (DECVI)
Term-End Examination
June, 2016
OOQOb
BIEL-037 MAINTENANCE OF ELECTRONIC EQUIPMENT Time 2 hours Maximum Marks: 70
Note: Attempt any five questions. All questions carry equal marks. Missing data may be suitably assumed.
1. Explain the differences between the traditional bathtub reliability curve and the generalized reliability curve. What is the significance of these curves in deciding the reliability of electronic equipments? 8+6=14
2. Differentiate among Thermal Acceleration, Electrical Acceleration and Damp Heat Acceleration.
3. Explain the troubleshooting procedure for the component failure. Write down the maintenance policy for the protection from electromagnetic interference. 7+7=14
4. What are the steps involved in the management of service manual and reference library, maintenance arrangement and calibration check? Explain in brief. 14
5. Explain the fundamental troubleshooting procedure involved in reading of block diagram, circuit diagram and working diagram. 14
6. Explain the following: 2x7=14
Functional Area Approach
Split-Half Method
7. Write short notes on any two of the following: 2x7=14
Work Bench
Fault Finding Aids
Diagnostic Software
Signal Injection and Signal Tracing
DIPLOMA -VIEP -ELECTRONICS AND
COMMUNICATION ENGINEERING (DECVI)
Term-End Examination
June, 2016
OOQOb
BIEL-037 MAINTENANCE OF ELECTRONIC EQUIPMENT Time 2 hours Maximum Marks: 70
Note: Attempt any five questions. All questions carry equal marks. Missing data may be suitably assumed.
1. Explain the differences between the traditional bathtub reliability curve and the generalized reliability curve. What is the significance of these curves in deciding the reliability of electronic equipments? 8+6=14
2. Differentiate among Thermal Acceleration, Electrical Acceleration and Damp Heat Acceleration.
3. Explain the troubleshooting procedure for the component failure. Write down the maintenance policy for the protection from electromagnetic interference. 7+7=14
4. What are the steps involved in the management of service manual and reference library, maintenance arrangement and calibration check? Explain in brief. 14
5. Explain the fundamental troubleshooting procedure involved in reading of block diagram, circuit diagram and working diagram. 14
6. Explain the following: 2x7=14
Functional Area Approach
Split-Half Method
7. Write short notes on any two of the following: 2x7=14
Work Bench
Fault Finding Aids
Diagnostic Software
Signal Injection and Signal Tracing
Other Question Papers
Departments
- Centre for Corporate Education, Training & Consultancy (CCETC)
- Centre for Corporate Education, Training & Consultancy (CCETC)
- National Centre for Disability Studies (NCDS)
- School of Agriculture (SOA)
- School of Computer and Information Sciences (SOCIS)
- School of Continuing Education (SOCE)
- School of Education (SOE)
- School of Engineering & Technology (SOET)
- School of Extension and Development Studies (SOEDS)
- School of Foreign Languages (SOFL)
- School of Gender Development Studies(SOGDS)
- School of Health Science (SOHS)
- School of Humanities (SOH)
- School of Interdisciplinary and Trans-Disciplinary Studies (SOITDS)
- School of Journalism and New Media Studies (SOJNMS)
- School of Law (SOL)
- School of Management Studies (SOMS)
- School of Performing Arts and Visual Arts (SOPVA)
- School of Performing Arts and Visual Arts(SOPVA)
- School of Sciences (SOS)
- School of Social Sciences (SOSS)
- School of Social Work (SOSW)
- School of Tourism & Hospitality Service Sectoral SOMS (SOTHSM)
- School of Tourism &Hospitality Service Sectoral SOMS (SOTHSSM)
- School of Translation Studies and Training (SOTST)
- School of Vocational Education and Training (SOVET)
- Staff Training & Research in Distance Education (STRIDE)
Subjects
- Advance Microprocessor And Architecture
- Analog And Mixed Mode Vlsi Design
- Analog Communication
- Analog Electronic Circuits
- Analog Integrated Circuits Design
- Antennas And Propagation
- Applied Electronics
- Audio and Video Engineering
- Basic Telematics
- Basics Of Electronics Engineering
- Bio Informatics
- Circuits and Networks
- Computer Architecture
- Computer Communication Networks
- Control Engineering
- Data Communication And Network
- Data Structures
- Device Modelling For Circuit Simulation
- Digital Communication
- Digital Electronics
- Digital Signal Processing
- Digital System Design
- Dip- ECE PCB Design & Testing
- Electromagnetic Field Theory
- Electronic Measurement And Instrumentations
- Electronic Measurement and Instruments
- Electronic Product Design
- Electronic Switching Circuits
- Embedded System Design
- Industrial Electronics
- Information Theory And Coding
- Linear Integrated Circuits
- Maintenance Of Electronic Equipment
- Micro Controller
- Micro Controllers
- Microelectronics Technology
- Microprocessor
- Microprocessor And Its Applications
- Microwave And Radar Engineering
- Modeling And Testing Of Digital Systems
- Multirate Systems
- Nano - Electronics
- Optical Fiber Communication
- Opto Electronics Communication Systems
- Power Electronics
- Principles of Communication Engineering
- Quantum Communication
- Rf Circuits
- Satellite And Tv Engineering
- Signal Compression
- Signals And Systems
- Technical English
- Television Engineering
- Wireless Communication